Français Deutsch Español Nederlands Português Italiano

Product & behind the scenes

316 stainless steel by the sea: what powder coating changes

mis à jour le 21 novembre 2026 8 min read
A person looks at a smartphone in front of a wooden locker station by the water

You are comparing three offers for equipment that will spend its summers a few dozen metres from the water. All three say “stainless steel”. One specifies “marine stainless steel”, another claims “1,000 hours of salt spray”, and the last says nothing more. None of this can be compared.

By the sea, how well a structure holds up depends on four things: the steel grade, the severity of the site, the surface preparation under the paint, and rinsing. Here is what the ISO 9223, ISO 12944-2 and ISO 9227 standards, the European design manual for stainless steel structures and the powder coating specifications say, followed by the three questions to ask.

Contents

Stainless does not mean unalterable

Stainless steel owes its resistance not to its thickness but to a passive film of iron and chromium oxides, 2 to 3 nanometres thick, able to re-form on its own when scratched. A notched paint coat, by contrast, stays notched. Chlorides break through this film at one point and prevent it from closing again: the corrosion that follows is localised, which is pitting. A second form sets in within crevices, where water gets in and oxygen does not.

ISO 9223 takes three factors into account: temperature and humidity, sulphur dioxide, and airborne salinity. Regular exposure to sea spray attacks as much as immersion, adds the European design manual: evaporation concentrates the salt there.

304 or 316: the difference is molybdenum

The NF EN 10088-1 standard, of December 2023, lists the grades and their composition. The two you will come across are 1.4301, known as 304, and 1.4401, known as 316. Here are the standard ranges, as the European design manual reproduces them from EN 10088.

1.4301 (304) 1.4401 (316)
Chromium 17.5 to 19.5% 16.5 to 18.5%
Nickel 8.0 to 10.5% 10.0 to 13.0%
Molybdenum not specified 2.0 to 2.5%
Pitting resistance index 17.5 to 20.8 23.1 to 28.5
Intended sites rural, urban and light industrial marine and industrial

Molybdenum stabilises the passive film against chlorides. The pitting resistance index quantifies it: chromium, plus 3.3 times molybdenum, plus 16 times nitrogen. It is an order of magnitude, not a single criterion. Above all, “marine stainless steel” is not standardised, whereas “1.4401 according to NF EN 10088-1” is. Ask for the second wording, and for which parts it applies to, fasteners included.

What your site rates on the official scales

ISO 12944-2, December 2017 edition, classifies atmospheres into six categories, from C1 to CX. The classification is measured on low-carbon steel or zinc test specimens exposed for one year. The C5-M label, still common in offers, no longer appears in this edition.

Category Thickness lost in one year Typical environment
C3 medium 25 to 50 µm coastal areas with low salinity
C4 high 50 to 80 µm coastal areas with moderate salinity
C5 very high 80 to 200 µm coastal areas with high salinity
CX extreme 200 to 700 µm maritime areas with high salinity

EN 1993-1-4, the Eurocode for stainless steel structures, quantifies exposure differently: you start from zero and subtract points.

  • From 1 to 10 km from the sea: 3 points.
  • From 250 m to 1 km: 7 points.
  • At 250 m or less, Mediterranean or Atlantic coast alike: 15 points.
  • No rain washing and no cleaning programme: 7 more points.

Below 7 points subtracted, the grid places the part in the 304 class; from 7 inclusive to less than 15, in the 316 class; at 15 or more, it calls for a more resistant grade. Equipment installed 200 m from the Mediterranean reaches those 15 points through distance to the water alone. The procedure applies only to load-bearing parts and says nothing about coatings: it measures the severity of a site, not what a painted station is worth.

Painting stainless steel: preparation, then labels

Powder coating provides colour, a barrier that keeps salt away from the metal, and a smooth surface. An organic coating is 20 to 200 µm thick, against 2 to 3 nanometres for the passive film: a thick barrier that cannot repair itself, laid over a thin barrier that can.

Everything then depends on surface preparation, because a poorly bonded coating is a moisture trap. Qualisteelcoat gives the measure. When preparation involves shot blasting, cleanliness to grade Sa 2½ of ISO 8501-1. Residual dust limited to class 1 of ISO 8502-3. Final rinse below 30 µS/cm. And, in classes C4 and C5, a pretreated part waits at most 8 hours before being coated, 3 hours if the air exceeds 70% humidity. For aluminium, Qualimarine requires a double chemical etch of at least 0.5 g/m² in alkaline and 0.7 g/m² in acid, then 60 µm on average. A seaside specification is read in grams removed and microns deposited.

Watch out for the labels cited: Qualimarine and Qualicoat apply to aluminium. For steel, it is Qualisteelcoat, which adopts categories C1 to C5 and aims for 15 to 25 years before the first repaint.

Class Duration in neutral salt spray
C2 240 h
C3 480 h
C4 720 h
C5 1,440 h, or 60 days

The detail that changes everything: the panels are scratched over 100 mm and down to the metal before the test, and the corrosion measured from the scratch must stay under 1.5 mm, or under 2 mm in class C5. Finally, two caveats. ISO 12944 excludes powder coatings from its scope, which makes any “C5 powder coating according to ISO 12944” approximate. And Qualisteelcoat specifies that its anti-corrosion requirements apply only to a limited extent to stainless steel, these specifications being calibrated on carbon steel, galvanised steel and aluminium.

Fasteners, crevices and fresh water

  • The fasteners. Stainless steel is almost always the cathode of the galvanic couple: it is its neighbour that suffers. The design manual advises against carbon steel bolts in a stainless steel part, the surface ratio being very unfavourable to them.
  • The crevices. An assembly out of the water must drain moisture, and inert deposits also create crevices that retain salts. All of this builds up first at the foot of the structure, hence the importance of the ground anchoring.
  • The rinsing. A wash, even a natural one from rain, maintains the appearance and extends the service life.

The International Stainless Steel Forum’s scale quantifies it: a location between 30 m and 1.6 km from salt water scores 3 severity points, and rinsing four times a year removes 2. A freshwater hose therefore counts as much, season after season, as the winterisation protocol.

The three questions to ask in writing

  • Which designation, on which parts? Not “marine stainless steel”, but the NF EN 10088-1 designation, for the sheet metalwork, the structure and the fasteners.
  • Which coating system? Surface preparation and its grade, conversion coat or not, guaranteed average and minimum thicknesses, specification applied.
  • Which test, with which criterion? The standard, the duration, scratched or unscratched panels, and the acceptance value. A duration alone is not a performance.

A fourth: what the warranty covers, and what it excludes.

FAQ

304 or 316 stainless steel by the sea?

316 contains 2.0 to 2.5% molybdenum that 304 does not, which stabilises its passive film against chlorides. The European design manual recommends 304 for rural, urban and light industrial sites, and 316 for marine and industrial sites.

Why powder coat a steel that is already stainless?

For the colour and for a 20 to 200 µm barrier that keeps chlorides away from the metal. The coating does not repair itself, whereas the passive film re-forms on its own: the stainless steel remains the safety net beneath the paint.

Is a thousand hours of salt spray a service life?

No: ISO 9227 sets neither a duration nor an interpretation of the results, and advises against using it to predict long-term performance. A duration only means something with the standard, the condition of the panel and the acceptance criterion.

Does Qualimarine apply to a stainless steel structure?

No, its specification covers the powder coating of aluminium. For steel, it is Qualisteelcoat, which itself specifies that its anti-corrosion requirements apply only to a limited extent to stainless steel.

How often should coastal equipment be rinsed?

The Eurocode asks for a wash at least every three months once a programme is recorded in the file. Fresh water is enough: the salt must be removed before it concentrates as it dries.

What we use, and why

The Wave-Up station is made of powder-coated 316 stainless steel, with 8 electric strike plates chosen to withstand sea fog. It is designed and made in France by our industrial partner. The manufacturer’s warranty covers 2 years, parts and labour, vandalism excluded. You can view it from every angle on our 3D model, and our five references are in the Hérault.

We publish the grade and the treatment, not a corrosivity class that we have not had certified. If you are comparing equipment for a coastal site, request a quote: you receive the detailed specifications and a price within 24 working hours, free of charge and with no obligation.

At a surf spot, the station spends the season facing the sea, in the spray. Our page on the self-service surfboard rental station covers this case: eight surfboards at the edge of the spot, a controller housed in a waterproof enclosure.

Sources

Share: LinkedIn X Facebook WhatsApp

Max

The Wave-Up team: solar lockers and self-service water sports.

How we write and check our articles

A Wave-Up station standing on a paved path, with no building work and no power connection.

The Wave-Up station, for real

A Wave-Up station standing on a paved path, with no building work and no power connection.

Eight boards stored upright, eight lockers for the vest and leash, and a QR code to book on the spot.

See the photos of stations in service

Get the next article

Leave a comment

Ready to go from content to action?

Estimate the revenue of a self-service rental station on your site, then request your free quote.

Request a quote